This clutch kit fits the following tractor models: 1641, 1641F, 2040S, 2140, 2355N, 2550, 2555, 2650, 2650N, 2750, 2755, 2850, 2855, 2855N, 2940, 2950, 2955, 3040, 3050, 3140, 3150, 3355, 3640, and 3640S. Kit contains: 12.875 inch, 10 spline spring driven disc (part number: AL70272), 13 inch, 27 spline single pressure plate (part number: R68485 or AL68486), pilot bearing, and alignment tool. It does not come with the release bearing. Additional $15.00 shipping due to weight. If you are ordering online, this additional charge will be added to your order after your receipt is printed. (Part No: R68485NKIT) $320.30. This cast iron pressure plate fits the following tractor models: 1641, 1641F, 2040S, 2140, 2355N, 2550, 2555, 2650, 2650N, 2750, 2755, 2850, 2855, 2855N, 2940, 2950, 2955, 3040, 3050, 3140, 3150, 3355, 3640, and 3640S.

It measures 13 inches in diameter, and has 27 splines, with a spline diameter of 1.75 inches. It replaces part numbers: AL68486, AL68485, and AL60308. Additional $15.00 shipping due to weight. If you are ordering online, this additional charge will be added to your order after your receipt is printed. (Part No: AL68486) $226.51.

4' x 7-1/2' overall, inlet & outlet#6 female o-ring with sight glass. R12 & R134A compatible. Models:1640, 2040, 2140, 2350, 2550, 2750, 2950, 2940, 4030, 4040, 4050, 4055, 4230, 4240, 4250, 4255, 4430, 4440, 4450, 4455, 4555, 4560, 4630, 4640, 4650, 4755, 4760, 4840, 4850, 4955, 4960, 7200, 7210, 7400, 7410, 7510, 7600, 7610, 7700, 7710, 7800, 7810, 8430, 8440, 8450, 8630, 8640, 8650, 8850, 9100, 9120, 9200, 9220, 9300, 9300T, 9320, 9320T, 9400, 9400T, 9420, 9420T, 9520, 9520T, 9620, 9620T. (Part No: RE49169) $35.74. 12 volt, 35 amp. For tractor models 925, 930VU, 932, 935, 942, 945, 952, 955, 965, 968, 975, 985, 940, (940 1980-84), 940V, 1030, 1030OU, 1030VU, 1035, 1035EF, 1035EV, 1040, (1130 1970-84), 1140F, 1140V, 1630, 1630OU, 1630VU, 1635, 1635EF, 1635EV, 1640, 1640F, (1830 1973-82), 1840, 1840F, (2020 1970-79), 2030, 2030OU, 2035, 2035EF, (2040 1976-82 with 164 dsl & 1979-85 with 152 dsl), 2040F, 2040S, (2120 1970-79), 2130, 2135, 2140, (2750 1983-86 with 239 dsl), (2840 1977-79 with 329 dsl), (2940 1980-84 with 359 dsl), (2950 1983-86 with 359 dsl), (3030 1979-82), 3130, 3135, 3140, (820 1968-72 with 3 cyl eng. & internal reg.), (830 1972-75 with 3 cyl), (920 1970-75), (930 1972-79), (1530 1974-75), (2150 1982-87 with 179 dsl), (2240 1976-82 with 164 dsl), (2255 1983-87 with 179 dsl), (2350 1983-86 with 239 dsl).

(Part No: ABO0208) $162.57. Single Pulley, call if you need a double pulley. 12 volt, 55 amp. For tractor models 1030, 1040, 1130, 1140, 1350, 1530, 1550, 1630, 1640, 1750, 1840, 1850, 1850N, 1950, 1950N, (2020, 2120, 2250, 2450, 2650, 2850 euro edition), 2040, 2040S, 2140, 2150, 2155, 2240, 2255, 2350, 2355, 2355N, 2440, 2550, 2555, 2650N, 2750, 2755, 2840, 2855N, 2940, 2950, 2955, 3030, 3040, 3050, 3130, 3140, 3150, 3350, 3640, 6100, 6200, 6200L, 6300, 6300L, 6400, 6400L, 6500, 6500L, 840, 940. (Part No: AL81436) $252.19. 12 volt, clockwise rotation, 13 tooth. This 2 Terminal Switch has many applications.

It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals.

The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch over all length.

Check measurements before ordering if using as a universal part. Applications include Ether Switch, Horn Button, Cold Start, Starter Switch and Manifold Heater Switch. Replaces: AR46184, AR47373, AR47374, R39554, R39554. (Part No: R7994) $11.25 Engine Bearings. For 2140, 2250, 2450, 2555, 2555TSS, 2650, 2750, 2755, 2755CS/TSS, 2855, 2855N, 3430, 3820, 945, 952, 1052, 1155, 2850, 310C, 310D, 315C, 315D all Turbo with 4.239T Diesel, 300 Series, 4 cylinder, 4.19' bore, 1.6' pin. Major Overhaul Kit includes: Piston Liner kit, Main Bearings set, Crank Seals, Connecting Rod Bearings/Bushings/Bolts set, Cam Bushing, Gasket Overhaul set.

2140 John Deere Clutch

When ordering, specify in comments Main Bearing Size of Standard,.010,.020 or.030, Thrust Bearing Size of Standard,.010,.020 or.030, Connecting Rod Bearing Size of Standard,.010,.020, or.030. Camshaft Bushing of out dia. 020 O/S or in dia. (Part No: RE54709) $936.55 Engine Parts.

This fuel pump is for diesel tractors: 830, 930, 1020, 1520, 2020, 2030, 2040, 2240, 2440, 2510, 2520, 2630, 2640, 2750, 2950, 2955, 3020, 3150, 3155, 4000, 4020, 4030, 4050(6359TP), 5020, 6030. Replaces OEM numbers AR42211B, AR49770, AR52159, DD14195, RE37482, AR102678, DD13483, RE37482, AR52729. Ports are 3/8 - 20 thread. The inlet is at 1 o'clock and outlet at 7 o'clock with the cam lever pointing toward you.

The inlet and outlet can be 'clocked' to a different position. Some applications may need different fittings, but thise are not supplied by Yesterday's Tractor. (Part No: TP-RE42211B) $28.02. 2.250 Offset 1.25' x 2.50' x 36.625' (.781 Holes at 1.125, 2.750, & 8.575') For 820 (3 Cyl), 830 (3 Cyl), 1020, 1520, 1530, 1640, 1641, 1830, 1840, 2020, 2030, 2040, 2130, 2140, 2141, 2240, 2250, 2251, 2350, 2351, 2355, 2440, 2450, 2541, 2550, 2555, 2630, 2640, 2650, 2651, 2750, 2755, 2850, 2855, 820, 830. ADDITIONAL $15 SHIPPING DUE TO WEIGHT. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED.

Drawbar pin available as part# L32016. (Part No: L29020) $181.79. This Hydraulic Pump has 1 1/16' Left inlet, 7/8' Top Inlet, 1 5/8 Right Inlet, 1 1/16' Discharge. Verify measuerments before ordering. It is used on 1550, 1640, 1750, 1830, 1840, 1850, 1950, 2030, 2040, 2130, 2140, 2155, 2250, 2350, 2355, 2440, 2450, 2510, 2520, 2550, 2555, 2630, 2640, 2650, 2750, 2755, 2840, 2850, 2855N, 2940, 2950, 2955, 300 Indust/Const, 3010, 3020, 3030, 3040, 3050, 3055, 3130, 3140, 3150, 3155, 3255, 3350, 3640, 3650, 4010, 4030, 500 Indust/Const, 5010, 600 Indust/Const, 9950 Cotton Picker, 9960 Cotton Picker, 9965 Cotton Picker, 9970 Cotton Picker. It replaces AR39168, AR90459, AR97872, R39695 (Part No: AR97872) $959.10. 40cm^3, 50cm^3 with serial plate, this kit is used on pumps that require the teflon sealing washer rather than the quad ring with backup washer, pump models EA1, GA1, GH1.

For tractor models 2510, 3010, 4010, 5010, 3020, 4020, (5020 SN# up to 0249999), 7020, 7520, 1830, 2130, 2030, 3030, 3130, 4030, 4230, 4430, 4630, 1640, 1840, 2040, 2040S, 2140, 2440, 2640, 2840, 2940, 3140, 4040, 4240, 4440, 4640, 4840, 2350, 2550, 3150, 4050, 4250, 4350, 4450, 2155, 2355, 2555, 2955, 3055, 3155, 3255, 4055, 4255, 4455. (Part No: RE29107) $61.89. Repairs AR103033 (23CMS) & AR103035 (11.3 CMS) Hydraulic Pumps. For JD 300, 301, 400, 401, 1020, 1120, 1130, 1140, 1350, 1520, 1530, 1550, 1630, 1640, 1641, 1750, 1830, 1840, 1850, 1950, 1950N, 2020, 2030, 2035, 2040, 2040S, 2120, 2130, 2135, 2140, 2141, 2150, 2155, 2240, 2250, 2251, 2251N, 2255, 2350, 2351, 2355, 2355N, 2440, 2450, 2541, 2550, 2555, 2630, 2640, 2650, 2650N, 2651, 2750, 2755, 2850, 2855, 2941, 2951, 301A, 302, 3030, 3040, 3050, 3120, 3130, 3135, 3140, 3141, 3150, 3340, 3350, 3351, 3640, 3641, 3650, 3651, 4010, 7440, 7445, 830, 840, 930, 940, 1040. Industrials: 301, 400, 401. (Part No: S-AR98993) $20.92.

Rockshaft Cover Gasket Kit (Lift Cover) includes a metal gasket. John Deere TRACTOR: 1040, 1140, 1350, 1640 (serial number 430, 000 and up), 1641, 1641F, 1750, 1840, 1850, 1950, 2040 (serial number 430, 000 and up), 2040S (serial number 430, 000 and up), 2140 (serial number 430, 000 and up), 2141, 2150, 2155, 2240, 2250, 2251, 2255, 2350, 2351, 2355, 2355N, 2440, 2450, 2541, 2550, 2555, 2640, 2650, 2651, 2750, 2755, 2840, 2850, 2855N, 2940, 2941, 2950, 2951, 2955 (before serial number 767517), 3040 (serial number 430, 000 and up), 3050, 3055, 3140 (serial number 430, 000 and up), 3141, 3150, 3155, 3255, 3350, 3351, 3640, 3641, 3650, 3651, 840, 940. Replaces AL57974 (Part No: AL57974) $50.77. This LED Floodlight is for 12-volt Negative Ground Systems only. It is polarity specific. It is a direct replacement for 4410, 4411 sealed beam or halogen. Features 6-LED, 1440 Lumens, 18 Watts.

4-1/2 Inch diameter. The flood beam is an excellent work light that illuminates wide and short areas. Replaces 239804, 1164605, 70239804, 71164605, 4410, A42294, A43639, A47179, D33182, L30464, 105774A, 209495, 251534, C0NN15330A, C5NN13007F, E3NN15330AA, 126470C1, 131203C1, 131348C1, 131508C1, 390756R91, AE31263, AR104119, AR21059, AT25451, H7606, RE285628, RE336111, RE35168, RE561116, 285871M1, 505281M1, 509652M91, 10P2645, 105774A, 166407A, 735606A (Part No: L4411LED) $48.10.

This PTO Shaft is 31.250 long, 6 spline, 540 RPM. It is used on some of the following: 1020 (W/ HEAVY DUTY PTO BEARINGS), 1030, 1040 (Serial Number 437370 and up), 1120 (W/ HEAVY DUTY PTO BEARINGS), 1130, 1140 (SN 437370), 1350, 1550, 1630, 1640, 1641F, 1750, 1850, 2030, 2040 (Serial Number 350000 and up), 2130, 2140, 2150, 2155, 2240 (Serial Number 350000 and up), 2250, 2255, 2350, 2355, 2450, 2550, 2555, 2750, 2755, 2855, 820 (3 Cyl.) (W/ HEAVY DUTY PTO BEARINGS), 840 (Serial Number 437370 and up), 920 (W/ HEAVY DUTY PTO BEARINGS), 940 (Serial Number 437370 and up) It replaces L28712, L38806. Verify measurements and OEM Numbers. (Part No: L38806) $351.32. Lucas Hub Oil was formulated to stop leaks in steering axles and trailer hubs on heavy duty trucks. It also allows hubs to run on a marginal amount of oil in case of a blown seal or poor maintenance.

It is an excellent gear lube for racing or heavy duty applications. Key benefits slows leaks, prevents downtime, extremely heat resistant, Very long lasting. (Part No: LU10088) $10.56 Electrical System - Don't see the Alternator you need for your tractor?

We have many alternators not listed on this website (for tractors 1953 & newer). Just call us at 800-853-2651. Lucas Assembly Lube (4 oz). Designed to be used as an initial lubricant to metal surfaces. It mixes with any oil and will not plug filters. This product clings to all surfaces and is an excellent rust inhibitor, allowing long term storage for all parts.

It is useful wherever tension or torque is applied. Key Benefits are: Use to pre lube camshaft, bearings, lifters and valve train. Prevents seizing, galling and scuffing perfect for engine lding, super slick and tacky, easy to use, excellent rust inhibitor, excellent for long term storage, contains Zinc, Moly and other extreme pressure additives for maximum protection during engine break-in. (Part No: 10152) $5.00 Engine Parts - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor). NOTE Engine Rings - Don't see the correct ring set for your tractor?

Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1.

Engine size & type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32'), 4.

Number and size of oil rings for each piston (Ex: (1) 5/32'). NOTE Exhaust System.

Lucas Fuel Treatment is formulated for both gasoline and diesel engines, carbureted or fuel injected. It gives your fuel system what it really needs - a blend of super slick oils and additives with a high detergent action that allows the engine to operate at maximum efficiency.

Also, it cleans and lubricates the carburetor and injectors and causes the fuel to burn more thoroughly for increased power and less fuel consumption. Lucas Fuel Treatment should definitely be used in vehicles that require leaded fuel because it actually replaces the benefits of lead in gasoline without causing harmful emissions. Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.A powerful blend of oils and additives that contain no SOLVENTS. Designed to increase power and fuel mileage and also lower exhaust emissions through a more complete combustion.

(Part No: LU10003) $10.67. Comes assembled complete with hardware. Easier hookup, spring loaded locking device. Adjustable top link ball bracket.

Includes 7/8 inch mounting pins and adapter bushings, 27-1/4 inches width, 3-1/2 inch x 3-1/2 inch beam. This is ONLY for tractors that have, a three point hitch already installed.

An additional shipping charge of $60 will apply due to the weight of this item. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: HF141101) $227.70. Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inches to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork.

For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269) $176.32. Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405.

Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269) $176.32. Tail Wheel and Hub Assembly with grease fitting.

4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600.

Wheel must be attached to fork. For Bush Hog cutters.

With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Part No: BH215) $106.08. 6 inch x 9 inch tail wheel assembly with laminated tire, less hub.

4 inch pilot, 5 bolt holes, 5-1/2 inch bolt circle. 5-1/4 inches wide, 21 inch outside diameter, 74#. Used mostly on pull Bush Hog models of the following series mowers: 109, 115, 126, 160, 166, 205, 206, 207, 220, 255, 256, 257, 268, 305, 306, 307, 310, 315, 405, 406, 502, 600, 1109, 1115, 1126, 1206, 1207, 1209, 1220, 1226, 1257, 1305, 1306, 1307, 1310, 1315, 1405, 1406, 1600, 2315, 2415, 2510, 2512, 2610, 2614, 2615, 3108, 3209, 3368, 3414, 3610, 4214, 4215, 12610, 12615, 13710, CR14R, CR20F. (Part No: 294) $124.93. 60 inches wide x 65 inches long, molded from virtually indestructible flexible U.V. Stabilized polyethylene, exclusive socket mounting system for torsion bars, no mounting bolts pass through molding.

Available in green, white, orange, blue, or red. Please specify in comments section which color you need. Hardware to mount to your ROPS sold separately. Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257X) $430.31.

45 inches wide x 60 inches long. Molded from virtually indestructible flexible U.V.

Stabilized polyethylene, exclusive socket mounting system for torsion bars NO mounting bolts pass through molding. Available in white, green, orange, blue, and red please specify in comments section which color you prefer. Hardware to mount to your ROPS sold separately. Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED.

(Part No: B257XSTD) $374.50. Deluxe Umbrella comes with universal mounting bracket. Four spring steel bows are locked into place with individual spring clips, providing ease of operation and a rigid framework.

Frame constructed of tubular steel. All metal parts are zinc plated for rust resistance. 54 inch square cover is made of durable polyester material.

Each corner is double reinforced. AVAILABLE IN RED, YELLOW, ORANGE, WHITE or BLUE.

State color desired in comments section of order form when ordering. (Part No: TU56-X) $155.22. A pure petroleum multi-use oil supplement. Controls noise, heat and wear in manual transmissions and differentials.

Number one in the heavy duty and high performance industries. Lucas Oil Stabilizer is a 100% petroleum product formulated to eliminate dry starts and reduce friction, heat and wear in any type of engine. It allows motor oils a higher degree of lubricity which reduces oil consumption and operating temperatures. Use Lucas Oil Stabilizer in gear oil to stop leaks, reduce operating temperatures and increase the life of the gear oil. Since it is pure petroleum. Key Features Increase oil life at least 50% longer, Reduces oil consumption, Eliminates dry starts, Raises oil pressure, and Increases power and miles per gallon. (Part No: LU10001) $15.12 PTO / Driveline.

AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D.

Tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke.

1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering.

(Part No: AB4111WY) $187.82. AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. Tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore.

John Deere 2140 Tractor Specs

Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length.VERIFY LENGTH BEFORE ORDERING.

(Part No: AB4111K33) $288.01. Universal Application Leatherette Suspension seat.

For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track.

IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is Black. Additional $30 shipping due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1050ATSP) $89.37.

BLUE Universal application leatherette suspension seat. For most compact, agricultural and industrial tractors.

Adjustable base for 5 different mounting angles, internal suspension weight adjustment, special slotted base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, adjustable slide track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR.

Color is BLUE. Add $15 additional shipping per seat due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1060ATSP) $89.37. Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors.

Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLACK.

(Part No: TS1075ATSP) $89.37. This Universal Vinyl seat has Multiple mounting holes, ranging from 4 inch to 11 inch center to center (front to back) and 6-1/2 to 13 inch center to center (side to side). Customer needs to verify it will work for their tractor. An adapter plate may need to be made for some models. Slide track for forward/rear adjustment. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR.

(Part No: TS1100) $117.53.YELLOW. Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track.

IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. Add $15.00 additional shipping due to weight.

Parts

IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1040ATSP) $88.39 Sheet Metal / Body Parts. This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn power Steering with an Eaton Pump.

Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting.

The shaft diameter measures.670 inches. The shaft length, where the pulley mounts measures.575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Part No: S03-1003) $384.33.

With embroidered John Deere logo. (Part No: JDGR) $19.95 Call 800-853-2651 to Order Or Click the 'Add to Cart' Button Customer Service Monday - Friday 9:00-6:30pm EST Order online anytime! Your Shopping is YESTERDAY's TRACTORS has been a leading tractor parts supplier on the internet since 1995. Join thousands of happy customers who have purchased parts and more for their antique tractor from us! Copyright © 1997-2018 Yesterday's Tractor Co. Antique Tractor Headquarters All Rights Reserved TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co.

Products and within the Yesterday's Tractor Co. Websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation.

Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.