Manual Mitsubishi Pajero Pinn
Applicable Manuals: Manual Pub. 3 DRIVE CYCLE Performing the running test of the car using the following five drive cycle patterns makes it possible to monitor all the diagnosis codes that are required for operation of the car in order to determine if the applicable system is operating properly or not. In other words, doing such a drive allows to regenerate any kind of trouble which involves illuminating the Engine Warning Lamp (Check Engine Lamp) and to verify the repair procedure has eliminated the trouble the Engine Warning Lamp (Check Engine Lamp) is no longer illuminated. Caution Two technicians should always be in the vehicle when carrying out a test drive. NOTE Check that the diagnosis code is not output before traveling in the Drive cycle pattern. Erase the diagnosis code if it has been output. DRIVE CYCLE PATTERN LIST PROCEDURE MONITOR ITEM DIAGNOSIS CODE 1 Catalytic converter monitor P0420 2 Heated oxygen sensor monitor P0130 3 Fuel trim monitor P0170 4 Feed back monitor P0125 5 Other monitor P0136, P0201, P0202, P0203, P0204, P0300, P0301, P0302, P0303, P0304, P0325 NOTE The vehicle speed sensor (P0500) and the power steering fluid pressure switch (P0551) are used to determine if the system is operating properly or not through use of the Data List function of the MUT-II.
Details:2001 GALANT Workshop Manual Supplement 4G64 2001 SPACE RUNNER/SPACE WAGON Workshop Manual Supplement 4G64 GDI - Troubleshooting. 4 PROCEDURE 1 Monitor item CATALYTIC CONVERTER MONITOR (P0420) One trip monitor from start to ignition switch to “LOCK” (OFF) position will be completed while traveling with the following drive cycle pattern. It will take 10 minutes or more. Drive cycle pattern Inspection conditions. Atmospheric temperature:-10 °C or more. Condition of A/T:Selector lever D range, overdrive switch “ON” position Test procedure 1.
Engine: start 2. Accelerate until the vehicle speed is 100 km/h or more.
Travel for 5 minutes or more while keeping the vehicle speed is 100 km/h or more. Decelerate until the vehicle speed is 100 – 120 km/h or less. While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 100 – 120 km/h and travel for 5 minutes or more. Stopping and braking during this operation are permitted. Return the vehicle to the shop, then turn the ignition switch “LOCK” (OFF) position. 2001 GALANT Workshop Manual Supplement 4G64 2001 SPACE RUNNER/SPACE WAGON Workshop Manual Supplement 4G64 GDI - Troubleshooting Y6005BY 100 – 120 km/h Vehicle speed 5 minutes or more 100 km/h or more Engine start Stopping and braking permitted Ignition switch ”LOCK” (OFF) position Time 5 minutes or more.
5 PROCEDURE 2 OXYGEN SENSOR MONITOR (P0130) One trip monitor from start to ignition switch to “LOCK” (OFF) position will be completed while traveling with the following drive cycle pattern. It will take 5 minutes or more. Drive cycle pattern Inspection conditions. Engine coolant temperature: 85 °C or more. Atmospheric temperature: -10 °C or more. Condition of A/T:Selector lever D range, overdrive switch “ON” position Test procedure 1.
Manual Mitsubishi Pajero Pinin
Engine: start 2. Manual electrical autocad 2017 en. Accelerate until the vehicle speed is 80 – 100 km/h. While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 80 – 100 km/h and travel for 5 minutes or more. Stopping and braking during this operation are permitted. Keep the accelerator pedal opening degree constant for 1 minute or more after each acceleration. Return the vehicle to the shop, then turn the ignition switch “LOCK” (OFF) position.
Mitsubishi Pajero Pinin 1.8 16v
2001 GALANT Workshop Manual Supplement 4G64 2001 SPACE RUNNER/SPACE WAGON Workshop Manual Supplement 4G64 GDI - Troubleshooting Y6002BY Vehicle speed 5 minutes or more 80 – 100 km/h Engine start Stopping and braking permitted Ignition switch ”LOCK” (OFF) position Time.